![]() ![]() Whenever you put a blade on your clipper follow with a tiny drop of oil in the middle of the teeth. It also prevents pet dander from melting and creating orange-colored buildup on your cutting surface. The oil keeps heat down and saves your cutting edges for months not weeks. When it spreads across the blade it will stay there for quite a while. That’s all you need.Īs you can see in the picture the drop of oil is very small. Start the clipper and let the oil spread as a thin coating across the blade. (8oz) Premium Lubricating White Oil for Hair Clippers Electric Shaver Oil Lubricant, Hair Clipper Blade Oil, Hair Clipper Oil, Beard Trimmer Oil, and Straight Razor Lubricant with Anti-Rust Protection 8 Fl Oz (Pack of 1) 4.7 (1,379) 1199 (1. It will seep through the teeth and get oil on the coat. Never run a bead of oil across the teeth. Whether resting on a table or on a clipper, put one tiny drop of oil in the center of the blade on the cutting surface. The first three points do need to be oiled again in the same day unless you wash the blade. Why? Because the dog hair you are cutting removes oil from blade teeth. Oiling teeth has to be done every time you put a blade on your clipper. That way I can start the clipper up right away and spread the oil across the cutting surfaces immediately. I prefer to oil the teeth while the blade is on a clipper. You can place the fourth drop on the cutter teeth while resting on the table or after placing the blade on a clipper. Next push your cutter back to the center of the blade. It may even cause the blade to cornrow and other problems. Without oil a dry blade guide causes the cutter to hesitate. If you don’t oil this groove at least once-a-day your blade may make a screeching sound and not cut properly. ![]() The first tiny drop goes on the rear rail just outside the left spring as shown and another on the rear rail outside the right spring where sliding the cutter over provided access.Īpply a third tiny drop in the groove on the top of the cutter. Start by putting one tiny drop of oil on both rear rails. Now you can access the first three points with oil. You should be able to see the rear rail on both sides of the spring. On the next page you will find pictures with my instructions to help you reap the benefits of proper oiling.įirst, push the cutter out to either side so that spring is lined up with the notch in the cutter. With practice you will be a natural soon enough and glad for it. However, if you wash a blade between grooms you need to oil all four points before using the clean blade. There are four points of a blade to oil but you only need to oil three of the four once-a-day. Most contain denatured alcohol which can be poisonous if inhaled. The list of safety gear you need to wear while spraying these aerosols are listed on the back of the can. These products can also cause health issues if you don’t wear the recommended safety gear. Coolants, WD-40, and Rem Oil evaporate quickly leading to friction, heat and the destruction of cutting edges in a short time. It stays on blades preventing friction, heat and pet dander buildup on cutting surfaces. I do not recommend them.īlade oil is the best form of lubrication. Some groomers turn to other forms of lubrication like Spray Coolants, Rem Oil or WD-40. ![]() If you over oil it drains through the teeth and onto pet coats. Most groomers apply too much oil when oiling clipper blades. If payment is not made within 14 days of the completion of services, then the tools will become the property of Clipper Pros, LLC.By Jeff Andrews, Northern Tails Sharpening Payment is expected at the time of completion of services. Large inventory of parts and accessories for clippers and trimmers. Use to lubricate and clean blades Easy to apply, simply brush off excess hair first and then with your clipper perpendicular to the ground apply a few drops to one side of the blade and run for a couple seconds. $5 each set (unless purchased from us or sharpened by us) Clipper oil stays on the blade and helps prevent friction, heat, and dander from sticking to the cutting surface. Skeleton the Andis T-Outliner, Outliner, GTX, or T-Outliner Blackout for heat distribution: $30 (Includes a cleaning, inspection, and tune-up) *Please Note: All prices listed above are our service fees and do not include the cost of replacement parts which will vary from repair to repair. WE ONLY REPAIR AND SERVICE ANDIS CLIPPERS AND TRIMMERS, OSTER CLIPPERS AND TRIMMERS, AND WAHL CLIPPERS AND TRIMMERS Clipper and Trimmer Repairs:Īll repair prices include cleaning, inspection, adjustment, and lubrication in addition to the repair(s) being completed. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |